Kia Sorento: Crankshaft Inspection

Kia Sorento (XM, 2011-2015) Service Manual / Engine Mechanical System / Cylinder Block / Crankshaft Inspection

Check the crankshaft bearing oil clearance.

(1)	To check main bearing-to-journal oil clearance, remove the main caps and bearing halves.

(2)	Clean each main journal and bearing half with a clean shop tower.

(3)	Place one strip of plastigage across each main journal.

(4)

Reinstall the bearings and caps, then torque the bolts.

Tightening torque :

14.7 N.m (1.5 kgf.m, 10.8 lb-ft) + 27.5 ~ 31.4 N.m (2.8 ~ 3.2 kgf.m, 20.3 ~ 23.1 lb-ft) + 120 ~ 125°

•	Always use new crankshaft main bearing cap bolts. Crankshaft main bearing cap bolts are toque-to-yield bolts designed to be permanently elongated beyond the state of elasticity when torqued, so if the bolts are removed and reused, it may cause the bolts to break or fail to maintain clamping force.

•	Do not turn the crankshaft.

(5)

Remove the cap and bearing again, and measure the widest part of the plastigage.

Standard oil clearance :

0.020 ~ 0.038 mm (0.00079 ~ 0.00150 in.)

(6)

If the plastigage measures too wide or too narrow, remove the upper half of the bearing, install a new, complete bearing with the same color mark (select the color as shown in the next column), and recheck the clearance.

Do not file, shim, or scrape the bearings or the caps to adjust clearance.

(7)

If the plastigage shows the clearance is still incorrect, try the next larger or smaller bearing (the color listed above or below that one), and check clearance again.

If the proper clearance cannot be obtained by using the appropriate larger or smaller bearings, replace the crankshaft and start over.

If the marks are indecipherable because of an accumulation of dirt and dust, do not scrub them with a wire brush or scraper. Clean them only with solvent or detergent.

Crankshaft Bore Identification Mark

Letters have been stamped on the block as a mark for the size of each of the 5 main journal bores.

Use them, and the numbers or bar stamped on the crank (marks for main journal size), to choose the correct bearings.

Cylinder Block Specifications

Calss	Mark	Inside Diameter
a	A	56.000 ~ 56.006 mm (2.20472 ~ 2.20496 in.)
b	B	56.006 ~ 56.012 mm (2.20496 ~ 2.20519 in.)
c	C	56.012 ~ 56.018 mm (2.20519 ~ 2.20543 in.)

Crankshaft Journal Identification Mark

Conform to read stamping order as shown arrow direction from #1.

Crankshaft Specifications

Class	Mark	Outside Diameter Of Journal
I	1	51.954 ~ 51.960 mm (2.04543 ~ 2.04567 in.)
II	2	51.948 ~ 51.954 mm (2.04519 ~ 2.04543 in.)
III	3	51.942 ~ 51.948 mm (2.04496 ~ 2.04519 in.)

Crankshaft Bearing Identification Mark

Crankshaft Bearing Specifications

Class	Mark	Thickness Of Bearing
AA	Blue	2.026 ~ 2.029 mm (0.07976 ~ 0.07988 in.)
A	Black	2.023 ~ 2.026 mm (0.07965 ~ 0.07976 in.)
B	None	2.020 ~ 2.023 mm (0.07953 ~ 0.07965 in.)
C	Green	2.017 ~ 2.020 mm (0.07941 ~ 0.7953 in.)
D	Yellow	2.014 ~ 2.017 mm (0.07929 ~ 0.07941 in.)

Selection Chart For Crankshaft Bearings

Crankshaft Identification Mark	Crankshaft Bore Identification Mark	Assembling Classification Of Bearing
I (1)	a (A)	D (Yellow)
	b (B)	C (Green)
	c (C)	B (None)
II (2)	a (A)	C (Green)
	b (B)	B (None)
	c (C)	A (Black)
III (3)	a (A)	B (None)
	b (B)	A (Black)
	c (C)	AA (Blue)